Descripción
SPECIFICATIONS
CORE FUNCTIONS OF GAS GENERATOR SET
1: Each ignition is controlled accurately by ECU (see enclosed picture)
2: Gas inlet is with Italian imported pressure-reducing valve (see enclosed picture)
3: Gas and air mixing is controlled by mixer imported from USA (IMPCO), electric governor is of Chinese top brand (see enclosed picture).
4: Ignition cable and sparkling plug are Chinese top brand
5: Engine protection functions (warning or stop engine when water temp is high, high oil pressure, high oil temp, high speed)
6: Show alternator and engine parameters by LCD screen.
7: Can realize “remote control” of the genset (optional)
8: Voltage output automatically adjusted by AVR module.
9: Rated output power is 60kw
PARAMETERS
The gas generator will require the following:
1: Gas inlet pressure: 1.5 bar – 5 bar
2: Methane content in the gas: 85% – 95%
3: Temperature: -30℃～40℃
4: Altitude: ≤ 4000m
5: Relative air humidity: ≤90％
6: The circulating water should be soft water, cooling water should be alkaline clean water, must not have rust compound, such as acid, chloride etc.
I: Hardness: 0.7～5.3me/L
II: Chloride: <150mg/L
III: PH: 7～8.5
Note:
After purification, the gas should have no liquid oil or water, the dust content of gas should be ＜10mg/m3, particle size of dust should be ＜50μm,sulfide ＜20 mg/m3. The purification of gas is very important to the life time of genset, the continuous running time should be less than 300 hours each time, then stop and maintain the genset, maintenance time should be about 3 hours each time.
GAS GENERATOR SET PARAMETERS
Genset model
60GFT, OPEN TYPE
Engine model
Deutz 6105
Engine Type
Water cooled, 4 stroke, cylinder inline
Genset rated output power
60kw
Rated voltage
380V
Phase
3 phase
HZ
50Hz
Rpm
1500 r/min
Power factor
0.8
Rated current
108A
Steady-state voltage regulation
≤±2％
The transient voltage regulation rate
≤±10％
Voltage settling time
≤1S
Voltage fluctuation rate
≤±0.5％
Frequency steady state regulation
≤0.5％
Frequency recovery time
≤3S
Frequency steady state regulation
≤0.5％
Voltage adjust range
95-105％
Heat consumption
≤7mj/kw.h
Oil consumption
≤1.0g/kw.h
Gas pressure
1.5-5 bar
Cylinders NO
6 cylinders in line
Bore
105mm
Stroke
130mm
Compression ratio
19:1
Start method
24V electric start
Big repair period
≥20000 hours
Noise level
≤90 Db
Intake method
Naturally aspirated
Ignition method
By sparkling plug
Pressure adjustment method
Adjust pressure automatically
Speed governng type
Electric governor
Lubricating method
Forced and splashed type
Cooling type
Closed cooling with radiator (100% copper)
Exhaust temp
≤650℃
Displacement
9.3L
Size
2350*980*1450mm
Weight
1250 kg
gAS eNGINE PARAMETERS
Engine power
68KW
Total displacement（L）
4.33
Engine model
Deutz 6105
Exhaust temp
≦650
Rated voltage
24V (electric start)
Shock range（mm/s）
≦0.4
Rated speed
1500
Intake method
Naturally aspirated
Power factor
0.8 (delay)
Ignition method
By spark plug
Heat consumption (kj/kw.h)
≦3000
Air consumption（m3/h）
15000
Gas pressure (kpa)
≧1.5
Start method
24v electric start
Oil consumption (g/kw.h)
≦1.0
Speed adjust method
By electric governor
Oil volume (L)
45
Cooling method
Closed with radiator
Water volume (L)
High temp 80
Low temp 60
Lubricating method
Radiator
Forced and splashed type
Hight temp radiator
Overhaul time (h)
20000
Protection class
IP21
Noise level (Db)
≦90
Insulation class
H
Cylinders NO
6
Generating rate
98%
Emission
EURO 3
gENERATOR SET PROTECTION FUNCTIONS
Alarm and stop for hight/low voltage
alarm for hight water temp
Alarm and stop for hight/low HZ
alarm for high oil temp
Alarm and stop for short circuit
alarm and stop for hight / low oil pressure
Alarm and stop for over speed
Alarm and stop for high current
GENSET CONTROL
The control system is fixed to one end of genset (on the top of alternator). Main switch adopts automatic smart air breaker, which has the protection function of higher current, low voltage etc.
It is with 4 protection module which can send alarms when there is high water temperature, high oil temperature, high oil pressure and high speed.
The output voltage is adjusted automatically (by AVR)
There is flow-charging device for battery in the cabinet.
tHE DASHBOARD CAN MONITOR THE FOLLOWING PARAMETERS:
3 phase AC output current and voltage
Low oil pressure alarm
Engine speed
HZ
high oil temp alarm
Water temp
Battery voltage
over speed alarm
Oil pressure
Alarm for high water temp
Oil temp
Alarm and stop for high current
TOTALLY OFFER LIST
NAME
QUANTITY
NAME
QUANTITY
Gas Engine
(with ignition cable, spark plug)
1 piece
Alternator
1 piece
Common base frame
1 piece
Silent shell
ATS system (without switch)
Control cable
1 set
Pressure-adjusted valve
1 piece
Air-gas mixer
radiator
1 piece
Tube fire blocker
1 piece
radiator
1 piece
Wave tube for exhaust
1 piece
tools
1 set
Battery, start cabinet
1 set
Operation book
1 set
ECU for ignition
1 piece
